Jump to content
Click here if you are having website access problems ×

Paul Thompson

Member
 View Profile  See their activity

  • Posts

    577

  • Joined

  • Last visited

 Content Type 

Everything posted by Paul Thompson

  1. Paul Thompson
    Matt I use a Farnell M8 Proximity switch part number 530-293 with Caterhams Stack bracket for the speedo. It also has the advantage of a LED to indicate a good signal. I sure you can check it out on the Farnell site.
  2. Paul Thompson
    Does anybody in the Guildford area have a cap headed 5/16th bolt to fix the damper to the lower wishbone - need to fix it before Cadwell .
  3. Paul Thompson
    Does anybody in the Guildford area have a cap headed 5/16th bolt to fix the damper to the lower wishbone - need to fix it before Cadwell .
  4. Paul Thompson
    I have 2 make me an offer
  5. Paul Thompson
    Thanks for that but how do you know when you when the bearing is in the right spot ?
  6. Paul Thompson
    How do you persuade the roller bearing back on to the half shaft ? Also does anyone know the oil seal part number
  7. Paul Thompson
    The Fireblade is 415kg ready to go with half a tank of petrol - not disclosing the weight of the lardy pilot
  8. Paul Thompson
    Fred Arrived today - now how is it best fitted ?? Thanks
  9. Paul Thompson
    But per Andy at Quaife they are having a problem with the nearside nut coming loose
  10. Paul Thompson
    Stupidly both right handed. Have you tried using a locknut or castellated nut instead of the nylock ? I have suffered from the same problem and Quaife I believe are now considering an alternative - lets hope it is a lefthand thread on the nearside. !
  11. Paul Thompson
    Stupidly both right handed. Have you tried using a locknut or castellated nut instead of the nylock ? I have suffered from the same problem and Quaife I believe are now considering an alternative - lets hope it is a lefthand thread on the nearside. !
  12. Paul Thompson
    Stupidly both right handed. Have you tried using a locknut or castellated nut instead of the nylock ? I have suffered from the same problem and Quaife I beleive are now considering an alternative.
  13. Paul Thompson
    Roger What fuel pressure do you have try increasing it slightly. Also have you fitted the full dyno jet kit with longer springs and I think the jets should be 175. Paul
  14. Paul Thompson
    Check the Speedy Cables or Caerbont web site for the tables
  15. Paul Thompson
    Put me down for a set
  16. Paul Thompson
    Steve I have a set I bought on the bulk buy last year - right sizes but not sure if they are the KN ones. At present fitted with Avon Slicks. Make me an offer
  17. Paul Thompson
    Speak to Andy at Speedy Cables 00 44 1639 732299 and use a Farnell sensor # 530293 with the Caterham Stack bracket on the front brake caliper - worked for me
  18. Paul Thompson
    Speak to Andy at Speedy Cables 01639 732299 about your speedometer. You also need the Stack speed sensor bracket from Caterham and a sensor from Farnell part # 530293.
  19. Paul Thompson
    After the winter have 2 front calipers , Ital A frame and an ignition lock left over any interest ?
  20. Paul Thompson
    Put me down for one as well
  21. Paul Thompson
    Try Eurosil 01207 523100
  22. Paul Thompson
    Shaun I am south of Guildford at Blackheath. Call me on 020 7491 9221
  23. Paul Thompson
    I have some seat runners out of a car I built last year that are surplus to requirements.You could try those with your existing seats. FWIW because of their design Tillets can not go that far forward
  24. Paul Thompson
    2 Standard Front Brake Calipers (less than 200 miles use) £50 each 2 Rear Light clusters £10 each 2 Pre drilled Carbon Fibre Rear Wing Protectors £ 50 the pair 1 Ignition lock & barrel £20 1 A frame for Ital Axel £25 2 Sets of adjustable seat runners £10 each All off 2002 Jame Whiting Fireblade
  25. Paul Thompson
    Propshafts do mangle sensors. I have done two so far when I slipped off the black stuff and am looking to change the location to the front disc.
×
×
  • Create New...