Paul D Jones

If you need it welding on contact me Paul. See My Car Here

testing Paul. See My Car Here

testing Paul. See My Car Here

Let me know who many clamps you want Paul. See My Car Here

Unilever closed its factory on the 25th of Feb and all but 15 people lost there jobs [605 people] I was retained untill the sale of he factory site had tacken place and the factory now stands empty I was give 90 days notice on the 2nd of March on the 6th of March I was mini bused to the Hull factory each day to work the remainder of the 90 days notice I am now on the dole for a week and start at Corus steel works in Scunthorpe on the 3rd of May 24 years worth of redundance money will be in my bank on Friday Trailler and an ELITE 5 speed suquentiual gearbox should be in the post very soon But as Blatchat goes members only [if it does] its good bye from me Yust a little plug for wheel carriers, welding, Duratec advice, fabrication and machining please note my E-mail paul.jones37@ntlworld.com phone 07970 916076 Paul. See My Car Here

Fit a MAZDA one no need for the wire then Paul. See My Car Here

Its easy enough if you are a good welder with TIG I have done this loads of times at work and at home If you use 5% silicone filler rods you should have a strong weld that will resist cracking Paul. See My Car Here

Yes Paul. See My Car Here

Yes thats me Call me 07970 916076 Paul. See My Car Here

The best test to see if the valve is properly lapped Is to use Oily's method but use engineers blue you only need a spot the size of a pin head and rotate the valve 370 deg anymore and you could be covering up little imperfections in the lapping After you have finished wash the head and all components grinding paste CAN cause a valve to stick in the valve guide with all the cost that goes with a bent valve Paul. See My Car Here

The main differance will be the engine position and the engine mounts Caterham engines tend to sit a little further forward in the chassie I can weld up engine mounts for you if needed If you need as much ground clearance as posiable you may want to dry sump the engine but this does not gain much compared to my Zetec I measured it wet sump on the Zetec and dry sump on the Duratec and I gained a full 16mm ground clearance [i have lifted my engine and gearbox a little and the lowest part for the car is the chassie rails and gearbox hoop] From a money point of veiw I hope your not faint harted Paul. See My Car Here

I am in Cleethorpes and have a Westfield and have changed from a Zetec to a Duratec with the SBD 233 kit 07970 916076 Paul. See My Car Here

I can weld it up for youif you post it/bring it to me DN350SN Paul. See My Car Here

I still say the air temp should measure the temp of the air and not a fair bit of conducted heat/temp from the engine block as it has to affect the ECU settings This is more important if you are sprinting your car just feel the heat soak from the block into all the other bits of the engine. Paul. See My Car Here

Is the air temp sensor in the air filter back plate If so move it To the bulkhead The trumpets on my engine get hot and the back plate also warms up so this would fool the air temp sensor, the bulkhead is as good a place as any Paul. See My Car Here

But by the time you have done a few you will wish you had removed the head Paul. See My Car Here

"You better sit down now, the price for 1 allen bolt in 12.9 grade M7 x 60 = 3.18€ or 2.16£. This is without nut." Almost into Titanium prices there Let me know if you want a price for Ti ones Paul. See My Car Here

Do it properly get the DTI out Paul. See My Car Here

I can weld alluminum at home if you need it welding Paul. See My Car Here

See here Paul. See My Car Here

"In my experience, disks lose feel and bite as they get thinner" More likly to be disc run out

Cost depends on what you need to buy Ie you will need Exhaust manifold engine mounts belhousing Some things could be used again Tb's if manifold mounted clutch [maybee] fuel pump etc if useing the same set up carbs or TB's my Zetec to Duratec has cost approx £6000 sale of the Zetec helped Paul. See My Car Here

Fluke motorsport have been doing these lightened discs for Westfields for a couple of years Ring Graeme and ask if he does them for Caterhams There is no need for vented discs on such a light car Paul. See My Car Here

The Ti one was cheaper 😬 Paul. See My Car Here

Well thats wrong 145 foot pound-force = 196.593603 newton meter 100nm and 90 deg as per Ford or if you have a keywayed crank and front pullies you only need to do it up tight enough to stop it falling off. Paul. See My Car Here