jackb_ms
-
Posts
4,180 -
Joined
-
Last visited
Content Type
Profiles
Forums
Blogs
Events
Blatmaps
Speed Championship Results
News
Website Help
Downloads
Gallery
Store
Everything posted by jackb_ms
-
The bugger is out! I tried creating a new thread into the material but that didn't work. When i was tightening the bolt the thread broke. So I used a number of drill bit and it finally started to spin which was then a question of using more drill bit to break the last part in half. Now waiting on the new balls from Redline! Jack
-
I've ordered a new RH side vertical link from Redline. The question is can I pull the vertical link off the assembly the disk brake / front hub assembly? Jack
-
Hi I've got 2 on order with Redline as well as other bits. The ball is completely stuck no movement at all. Is the material of the ball strong enough to have a thread cut into it? Jack
-
Thanks The cups are bone dry and one of the ball half of it is still in the cup. Not sure how best to remove the other half. Jack
-
Hello Should there be grease around the ball of the front anti roll bar? If yes which type? Jack
-
Hello All I have been refreshing the front suspension and it looks like i am going to need a new RH side vertical link. Is it possible to pull it off using a bearing puller? Is there an assembly / disassembly guide somewhere? Cheers Jack
-
Hello All I have also been thinking of upgrading my suspension. Simon which system would you recomend? Jack
-
Is there a marking on rubber hose which are E10 proof? What about all the "O" rings in the fuel system are they E10 proof? Jack
-
What is the difference between a semi and fully synthetic oil? I have been using Fuchs Titan Race Pro S 5W-40 Ester Fully Synthetic which also available as a 10-40W Jack
-
I've used some aquarium air line in the past. Jack
-
Hello The old laptop I have has Windows XP on it and the battery life is short. I'll check it tonight and let you know the result. If it helps I will be in Uxbridge tomorow. Jack
-
Hello I have a couple you could borrow if you want. I would need them back. I'm near Oxford Jack
-
What about grease gun? Which one would you recommend? Jack
-
How does a 6 point harness works with the traditional Caterham seat? Jack
-
Is it possible to have one with the "21" logo? Jack -
It did produce a good result. The handbrake is now a lot better. Jack
-
Hello All I've done the adjustment and it took about a couple of hours. Jack
-
Hi Geoff Thank for the tip I'll have a go at it tonight Cheers Jack
-
Thanks all I have ordered the more expensive version as i will be able to use it on my other vehicle (and it comes in a nice plastic box ). I've ordered some brake cleaning fluid as well, hopefully I will be able to sort it. Jack
-
Hello Thanks you for the information. I'll check all that at the weekend For the windback tool, would this unit work from screwfix work: https://www.screwfix.com/p/hilka-pro-craft-brake-caliper-rewind-tool/4119R?kpid=4119R&ds_kid=92700044021103765&ds_rl=1241687&ds_rl=1245250&ds_rl=1243318&ds_rl=1245250&gclid=Cj0KCQjwpPHoBRC3ARIsALfx-_KT4dzEZoHXbi4cbn4j5Tu-B4BaoCozAtJDVkTfLjIkDv3ZTQkhHqkaAkmgEALw_wcB&gclsrc=aw.ds Or do I need something more specific? Jack
-
Hello All I have a issue with rear brakes on my 21, the two wheels are not brake the same when using the handbrake. What is the best method to rectify this issue? Jack
-
Steve How did you do that? Is that a bespoke design from Oxted? I have been looking a the the Willians harness and it seems a combination of the Silverstone LDT6 Caterham - and the Club 6 x 6 Saloon - may do the trick I'll see if I can pop round on Friday as they are not too far from me. Jack
-
Thank you for your comments all. The million pound question which one would you recommend? Jack
-
Thank What about a 5 point? Jack
-
Hello all Is it possible to fit 6 points harness with the standard cloth seat? Jack
