richardm57

here

drilled discs.

Hi all,

I also want to do this conversion.

Have Midas Metalcraft tubular top link fitted (about 1990 i think) with screw in ball joint which does allow camber change.

The later lower wishbone will not fit early chassis this has metalastic bush on front of chassis with 1/2 inch bolt.Have to modify front chassis for this.

But all is not lost am going to try these as my trunnions are 🙆🏻sed.[http://www.canleyclassics.com/products.asp?article=catkit1.xml]

they have trunnion type fitting on bottom.

The single piece top wishbone has a bracket which fits on the rear of the front anti roll bar bolts.

They did have grooved discs as well on website but cannot find at moment.

from richard.

hi Dennis,

am interested what size inlet pipe.

Richard

Hi,

Could you please tell me the dia. of inlet pipe for this.

thanks Richard.

hi,

try gartrac 01428682263

richard

Hi Andrew,

That must have been me.

Just left the top of car park,been watching a few planes.

Managed to miss most of the traffic hope you did to.

Richard.

hi Tim,

Redline sent a cable to me which would not fit.

i need cable with about 6to7inch free inner length.

thanks but will have to pass on your cable as inner to short.

thanks from richard.

hi mark.

only needed for spare so no problem.

thanks from richard.

hi,

clutch cable for bda or xflow required.

surrey area.

thanks from richard.

Hi all,

For ap 71/4inch twin plate. prefer one gear type CP3822-10FM3,none in stock.

one CP2822-31FM3.

Or back to back type.

thanks from richard.

hi,

i would think this paint is [Nextel] a 3M product.

it is easy to spray but is a 2 pack paint.

and it is suposed to represent suede or velvet finish.

i have a pair of Celestion SL600 speakers finished in this they are made Aerolam aluminium honeycomb.this was the original finish.

this was also used on the inside of ford transit bus doors.

it is very hard wearing and easy to clean as long as it has not worn to much.

richard.

hi mark,

will take some pics tomorrow

THiS WILL NOT BE A PRETTY SITE. 😬 😬

richard.

well not really. this was found in one of my lockups i did not know it was there.

alfa gtv type, v reg.

has been stripped of paint and most fittings, has box of parts lights,bumpers etc.

the body is rusty,flat tyres.

i could post pics but nobody will come and look if i do.

any takers

i should say easy repair 😬 😬 😬

but i dont think so.

nr.to guildford surrey

hi all,

the diff mountings if so are they any good.

i ask this as the newer bushes have thicker metal outer and inner sleeves.

this reduces the rubber by about 30%.

thanks from richard.

carb or injection for early 7

richard

have new handbrake cable for dedion with rear drum brakes this was made special order from Red Line.

i need one for calipers.

richard

for early dedeion with calipers.

have new cable for dedion with drum rear brakes.

richard

hi all.

atlas lathe do not know the model no. (has worn off). have parts book.

10 inch swing

2 chucks. single phase. overall lenth 39inch. one pulley not fitted on motor.

cover missing on front.

this will NOT be as accurate as a new cnc machine but serves a purpose.

no proper base, is on rough wood bench at present.

do not know what this is worth so will say £250 but if interested make an offer.

can be seen near to Dunsfold, Surrey Sussex border.

here

http://i36.photobucket.com/albums/e49/richardm57/lathe3.jpg

richard.

but it is on an xk150.

thats no good.

richard

hi. i believe cheesman did the road Mclaren

richard

hi, sounds like wheels are group 4 rally type for larger dia. studs.

I have a couple of this type of wheel and on the conical they have steel inserts check with supplier.

richard.

hi,

yes it is a star wheel.

it is on one of upper diagonals a bit difficult to find but mine adjusted ok when found.

richard.