BrettJ

PGM may have some.

@ D Jones, I've just measured my S3 and it 430mm max.

@ Neil Bolton, I have an S3 if you need some measurements

@ bluenose, could you please email Steve to place your order at steve@ycplastics.co.uk

@ dave@starcraft & Neil Bolton, I've asked if he does a SV version, I'll update once I hear back.

@ Bucko, could you please email Steve to place your order at steve@ycplastics.co.uk

@ Neil Bolton, yes they'll need some fettling to fit, especially if you wish for it fit inside the scuttle at the front. This requires you to heat the plastic and curve the front profile as these are straight when made.

Is anyone looking for a set of half doors, these are the carbon effect ones made out of ABS plastic by Steve at YC Plastics, which is much safer than real carbon should you have an accident IMO. I need four additional orders for these to go into production. The price are £100 per pair + £15 shipping within the UK. Please could you email Steve directly steve@ycplastics.co.uk

Image source: https://www.caterham7diaries.com/post/fuse-and-relay-box-layout

On 420R the diagram by Mark is more accurate than the manual, however the labels are misleading, as having both heated seats on popped the 20A fuse for the "Instruments"

Can anyone confirm if I require the Caterham High Level Brake Light Loom for 2018 car, or does it have a different connection?

If you runners are repairable, I'll be interested in swapping them for my set of fixed runners.

I used an electric sander and took off about 1.5mm off the face which comes into contact with the sump, so the holes could line up.

Just remember you may have to tilt the seat inwards or it binds on the side skin when using the spaces.

I have a Caterham 6 speed that need repairing, something got between the third gear and it's counter part and forced the gears apart cracking the casing. Let me know if you're interested.

This happened to me and the only solution I found to work was to move the ring back into postilion and use electrical tape to wrap around the shaft to build up 2-3 millimeter shoulder to prevent it move out of alignment again. The shaft was replaced under warranty in the end, as I believe you can not buy replacement rings.

@ DanRo, thank you. Will be  scouting that route out tomorrow.

@Benton, will give CaliMoto a go too

Can anyone recommend any good roads in surrey?

Hi Jeff,

Could you please share the dimensions as I'm looking to fit my roller barrels soon too?

Yes I do have it, and it was £158 including the postage. For what it is I still thought it was over priced.

It's a Duratec.

I would like to wire a remote switch for the rad fan and I'm looking for advice the best way to do this. Should I just connect another feed directly to the fan or should trick the ECU by supplying 12v to the temp sensor. Has anyone does this before?

Ok so it's not as straight forward as I thought, I'll looking to the logging. Thank you.

Does anyone have or know of a user guide for the Easimap 6 software and what the settings should be for a 2.0l Duratec? I would like to resolve the idling issue when cold and I would like to check the fueling map. I know that I won't be able to modify anything, I just want to check every is as it should be.

@David_Long, I don't suppose you have a similar video for the BMW diff?

Does anyone know where Caterham is getting their seat runners from, they're asking £76 for a pair for one seat?

Thank you, I didn't fix the ring, I just moved back into position. The car is 2019 model but only has done +/- 450 miles

Does anyone have a photo of their half shaft with the Speedo ring which they can share? I have already moved mine back in position once and clearly it wasn't enough as after 2 miles it shifted again. So I'm would like to know where about it should be on the axle in relation to the CV boot or Speedo sensor. (S3 BMW diff)

Any advise on how prevent this happening again would be appreciated too.

This is now sold. Thank you